MATERIAL SAFETY DATA SHEET SLIP-STOP TYPE PB

1. PRODUCT NAME : PALLETIZING ADHESIVE “PALLETIZING SLIP-STOP” TYPE “PB” “PBW”
2.MAKER’S NAME : KMG INC
ADDRESS : 348-10, SEOK KOK-RI, SEONG NAM-MYEON, CHEON AN, CHOONG NAM, KOREA
3. PREPARED DATE : NOVEMBER, 2001
4. HAZARDOUS INGREDIENTS : NO HAZARDOUS INGREDIENTS
5. SPECIFIC GRAVITY : 1.0 6. MELTING POINT : NOT APPLICABLE 7. PH : 6 - 7
8. VAPOR PRESSURE (mm Hg) : NOT APPLICABLE 9. VAPOR DENSITY : NOT APPLICABLE
10. EVAPORATING RATE : 1
11. BOILING POINT : 212 DEGREE F.
12. SOLUBILITY IN WATER : INFINITE
13. APPEARANCE AND ODOR : WHITE MILKY FLUID, BLAND ODOR
14. FLASH POINT : NONE (NONFLAMMABLE)
15. EXTINGUISHING MEDIA : NOT APPLICABLE
16. SPECIAL FIRE EXTINGUISHING PROCEDURE : NOT APPLICABLE
17. UNUSUAL FIRE AND EXPLOSION HAZARDS : NONE
18. STABILITY : STABLE 19. INCOMPATIBILITY (MATERIALS TO AVOID) : NONE
20. HAZARDOUS POLYMERIZATION : WILL NOT OCCUR, CONDITIONS TO AVOID - NONE
21. HAZARDOUS DECOMPOSITION OR BYPRODUCTS : NONE
22. ROUTE OF ENTRY: SKIN – NOT APPLICABLE, INGESTION – NOT APPLICABLE
INHALATION – NOT APPLICABLE
23. HEALTH HAZARDS (ACUTE AND CHRONIC) : NONE
24. SIGNS AND SYMPTOMS OF EXPOSURE : NOT APPLICABLE
25. MEDICAL CONDITIONS : GENERALLY AGGRAVATED BY EXPOSURE – NONE KNOWN
26. EMERGENCY AND FIRST AID PROCEDURES :
SKIN & EYE CONTACT – NOT PRIMARY IRRITANT. FLUSH EYES 10 MINUTES WITH CLEAN WATER
SEE PHYSICIAN IF IRRITATION PERSISTS.
INGESTION – NOT ACUTELY TOXIC. CONTACT PHYSICIAN.
27. PRECAUTIONS FOR SAFE HANDLING AND USE : STEPS TO BE TAKEN IN CASE OF MATERIAL
RELEASED OR SPILLED – PICK UP OR ABSORB LARGE VOLUME. FLUSH AREA WITH WATER.
28. WASTE DISPOSAL METHOD: SANITARY LANDFILL OR SEWER.
OBSERVE ENVIRONMENTAL REGULATIONS.
29. PRECAUTION TO BE TAKEN IN HANDLING AND STORING : KEEP FROM FREEZING.
30. OTHER PRECAUTION : NONE
31. RESPIRATORY PROTECTION : NOT REQUIRED.
32. VENTILATION : LOCAL EXHAUST/SPECIAL/MECHANICAL/OTHERS – NOT APPLICABLE
33. PROTECTIVE GLOVES : RUBBER AS DESIRED. 34. EYE PROTECTION: GOGGLES AS D

MATERIAL SAFETY DATA SHEET SLIP-STOP TYPE PE

1. PRODUCT NAME : PALLETIZING ADHESIVE “ SLIP-STOP” TYPE “PE”
2.MAKER’S NAME : KMG INC.
ADDRESS : 348-10, SEOK KOK-RI, SEONG NAM-MYEON, CHEON AN, CHUNG NAM, KOREA
3. PREPARED DATE : MAY, 2008
4. HAZARDOUS INGREDIENTS : NO HAZARDOUS INGREDIENTS
5. SPECIFIC GRAVITY : 1.10 6. MELTING POINT : NOT APPLICABLE 7. PH : 7 - 9
8. VAPOR PRESSURE (mm Hg) : NOT APPLICABLE 9. VAPOR DENSITY : NOT APPLICABLE
10. EVAPORATING RATE : 1 11. BOILING POINT : 80 – 100 DEGREES C.
12. SOLUBILITY IN WATER : UNLIMITED
13. APPEARANCE AND ODOR : YELLOW-BROWN FLUID, SLIGHT ODOR
14. FLASH POINT : NONE (NONFLAMMABLE)
15. EXTINGUISHING MEDIA : NOT APPLICABLE
16. SPEICAL FIRE EXTINGUISHING PRECEDURE : NOT APPLICABLE
17. UNUSUAL FIRE AND EXPLOSION HAZARDS : NONE
18. STABILITY : STABLE 19. INCOMPATIBILITY (MATERIALS TO AVOID) : NONE
19. HAZARDOUS POLYMERIZATION : WILL NOT OCCUR, CONDITIONS TO AVOID - NONE
20. HAZARDOUS DECOMPOSITION OR BYPRODUCTS : NONE
21. ROUTE OF ENTRY: SKIN – NOT APPLICABLE, INGESTION – NOT APPLICABLE
INHALATION – NOT APPLICABLE
22. HEALTH HAZARDS (ACUTE AND CHRONIC) : NONE
23. SIGNS AND SYMPTOMS OF EXPOSURE : NOT APPLICABLE
24. MEDICAL CONDITIONS : GENERALLY AGGRAVATED BY EXPOSURE – NONE KNOWN
25. EMERGENCY AND FIRST AID PROCEDURES :
SKIN & EYE CONTACT – NOT PRIMARY IRRITANT. FLUSH EYES 10 MINUTES WITH CLEAN WATER
SEE PHYSICIAN IF IRRITATION PERSISTS.
INGESTION – NOT ACUTELY TOXIC. CONTACT PHYSICIAN.
26. PRECAUTIONS FOR SAFE HANDLING AND USE : STEPS TO BE TAKEN IN CASE OF MATERIAL
RELEASED OR SPILLED – PICK UP OR ABSORB LARGE VOLUME. FLUSH AREA WITH WATER.
27. WASTE DISPOSAL METHOD: SANITARY LANDFILL OR SEWER.
OBSERVE ENVIRONMENTAL REGULATIONS.
28. PRECAUTION TO BE TAKEN IN HANDLING AND STORING : KEEP FROM FREEZING.
29. OTHER PRECAUTION : NONE
30. RESPIRATORY PROTECTION : NOT REQUIRED.
31. VENTILATION : LOCAL EXHAUST/SPECIAL/MECHANICAL/OTHERS – NOT APPLICABLE
32. PROTECTIVE GLOVES : RUBBER AS DESIRED. 33. EYE PROTECTION: GOGGLES AS DESIRED.
34. OTHER PROTECTIVE CLOTHING / EQUIPMENT : NONE
35. WORK AND HYGIENIC PRACTICES : GOOD MANUFACTURING PRACTICES